RESUMO Este estudo avaliou a influência do modo e do tempo de evaporação do solvente na resistência à tração (RT), resistência à flexão (RF) e módulo de elasticidade (MR) de dois sistemas adesivos: Scotchbond Multipurpose (SBMP) e Clearfil SE (CSEB). Para isso, amostras retangulares (2x1x7 mm) foram preparadas com 10 μL de primer e os solventes foram evaporados com aerossol a (23±1) ºC, (40±1) ºC e controle negativo (sem aerossol). Para cada temperatura, foram avaliados os tempos de 5, 20, 30 e 60 segundos. Os resultados estatísticos mostraram que a evaporação a (40±1) ºC resultou em melhor MR para os dois adesivos testados e todos os tempos de evaporação avaliados. No entanto, não houve diferenças significativas entre os tempos e modos de evaporação na RT. Os resultados deste estudo indicam que a evaporação a uma temperatura de (40±1) °C poderia melhorar o módulo de elasticidade de ambos os adesivos testados, independentemente do tempo de evaporação.

ABSTRACT This study evaluated the influence of the mode and time of solvent evaporation on the tensile strength (TS), flexural strength (FS) and elastic modulus (EM) of two adhesive systems: Scotchbond Multipurpose (SBMP) and Clearfil SE (CSEB). For this purpose, rectangular samples (2x1x7 mm) were prepared with 10 μL of primer and the solvents were evaporated with air spray at (23±1) ºC, (40±1) ºC and negative control (without spray). For each temperature, the times of 5, 20, 30, and 60 seconds were investigated. The statistical results showed that evaporation at 40±1ºC resulted in better EM for the two adhesives tested and all the evaporation times evaluated. However, there were no significant differences between the times and modes of evaporation for TS. The results of this study indicate that evaporation at a temperature of (40±1) °C could improve the elastic modulus of both adhesives tested, regardless of the evaporating time.

Abstract This study aimed to evaluate the physical properties and antifungal activities of polymethyl methacrylate (PMMA) acrylic resins after the incorporation of chlorhexidine diacetate salt (CDA). Methodology: First, acrylic resin specimens were fabricated with Vipi Cor® and DuraLay® resins with and without the incorporation of 0.5%, 1.0% or 2.0% CDA. The residual monomer and CDA release were measured at intervals ranging from 2 hours to 28 days using ultraviolet spectrometry combined with high-performance liquid chromatography. The antifungal activity against C. albicans was evaluated with the agar diffusion method. Fourier transform infrared spectroscopy was used to analyze the degree of resin conversion. Finally, the water sorption values of the resins were also measured. Results: The incorporated CDA concentration significantly changed the rate of CDA release (p<0.0001); however, the brand of the material appeared to have no significant influence on drug release. Subsequently, the inhibition zones were compared between the tested groups and within the same brand, and only the comparisons between the CDA 2% and CDA 1% groups and between the CDA 1% and CDA 0.5% groups failed to yield significant differences. Regarding the degrees of conversion, the differences were not significant and were lower only in the CDA 2% groups. Water sorption was significantly increased at the 1.0% and 2.0% concentrations. Conclusions: We concluded that the incorporation of CDA into PMMA-based resins enabled the inhibition of C. albicans growth rate, did not alter the degrees of conversion of the tested resins and did not change the release of residual monomers.

Abstract The aim of the present work was the obtaining and characterization of dental hybrid composites using nanoparticles (clay or silica) and boron-aluminum-silicate microparticles. We evaluated the dispersion of the nanofillers when changing their loading among 2.5%, 5%, 10% and 25% wt. Were tested, in the above quantities, four different types of nanofillers, two nanosilicas and two nanoclays The remainder of the inorganic phase, up to a total loading of 75% wt, was given by the boron-aluminum-silicate microparticles. The systems were characterized by XRD, TGA, LF-NMR, and . FTIR was used to determine the degree of conversion. The XRD and LF-NMR showed that the composites with 2.5% of clays, contained an exfoliated profile, and the groups with higher amounts of clay showed intercalated areas or the agglomeration of these particles. Furthermore, the silicas were agglomerated in all groups. The thermal resistance of the material was not affected by the silicas, but improved when using 2.5% of nanoclays. On the other hand, the addition of these particles caused the reduction of the degree of conversion of the systems.

The aim of this study was to obtaining an adhesive made of dimethacrylate copolymer and clay particles in different concentrations. The samples were prepared by light curing and were evaluated by XRD, FTIR and TGA as well as by measuring flexural strength, elasticity modulus and tensile resistance. The XRD and the mechanical test results indicated that the system with 0.2% clay is exfoliated, while the highest concentrations showed the agglomeration of these clays. FTIR was used to determine the conversion, and showed that use of clays particles are unable to significantly alter the polymerization until 1.0%. However, for the group containing 1.5%, there was a decline in this index. In the thermogravimetric analysis, only the groups with 0.2% of clays showed increased thermal resistance. In conclusion, the incorporation of clay at 0.2% concentration produces a well-dispersed system and can be applied as a dental adhesive.